Voltage Limiter and Schmitt Trigger MCQ’s

Read Time:1 Minute, 51 Second

This set of Linear Integrated Circuits Multiple Choice Questions & Answers (MCQs) focuses on “Voltage Limiter and Schmitt Trigger”.

1. Determine the upper and lower threshold voltage

Determine the upper and lower threshold voltage from given circuit

a) VUT = +14.63v, VLT= +14.63v
b) VUT = -14.63v, VLT= -14.63v
c) VUT = VLT= ±14.63v
d) None of the mentioned

2. What happens if the threshold voltages are made longer than the noise voltages in schmitt trigger?
a) All the mentioned
b) Enhance the output signal
c) Reduce the transition effect
d) Eliminate false output transition

3. Which circuit converts irregularly shaped waveform to regular shaped waveforms?
a) Schmitt trigger
b) Voltage limiter
c) Comparator
d) None of the mentioned

4. To a schmitt trigger in non-inverting configuration an input triangular wave of 1Vp is applied. What will be the output waveform, if the upper and lower threshold voltages are 0.25v?
a) Square waveform
b) Pulse waveform
c) Sawtooth waveform
d) Cannot be determined

5. Calculate the hysteresis voltage for the schmitt trigger from the given specification:
R2 =56kΩ , R1 = 100Ω ,Vref = 0v & Vsat = ±14v.

Calculate the hysteresis voltage for the schmitt trigger from the given R1 & R2 specifications

a) 0 mv
b) 25 mv
c) 50 mv
d) -25 mv

6. For the circuit shown below, obtain output waveform. Assume zener voltage to be 4.78v and voltage drop across the forward biased zener to be 0.7v.

Determine the output waveform from the given circuit

a)
Find voltage drop across the forward biased from the given diagram
b)
Find positive half cycle of the input waveform from the given diagram
c)
Find negative half cycle of the input wave from the given diagram
d)
Find forward biased zener to 0.7v from the given diagram

7. In which configuration a dead band condition occurs in schmitt trigger
a) Differential amplifier with positive feedback
b) Voltage follower with positive feedback
c) Comparator with positive feedback
d) None of the mentioned

8. How to limit the output voltage swing only to positive direction?
a) Combination of two zener diodes
b) Combination of zener and rectifier diode
c) All of the mentioned
d) Combination of two rectifier diodes

9. A basic op-amp circuit has a zener and rectifier diode connected in the feedback path. Calculate the maximum positive voltage. Where, zener voltage = 5.1 v and voltage drop across the forward biased zener = 0.7v?
a) VO = 5.8v
b) VO = 9.9v
c) VO = 4.7v
d) VO = 7.1v

10. Use the specification and obtain the output voltage swing for op-amp comparator.
Specification: R= 1kΩ; RL=10kΩ; VZ=6v; VSat=±15v (Assume forward bias of zener = 0.7v).

Determine the output voltage swing for op-amp comparator circuit

a)
Find the op-amp comparator from the given diagram
b)
Find the negative half cycle of VO from the given diagram
c)
Find the zener diode in feedback from the given diagram
d)
Find the feedback path limits VO from the given diagram

Happy
Happy
0 %
Sad
Sad
0 %
Excited
Excited
0 %
Sleepy
Sleepy
0 %
Angry
Angry
0 %
Surprise
Surprise
0 %

Average Rating

5 Star
0%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Leave a Reply

Your email address will not be published. Required fields are marked *

Previous post Comparator MCQ’s
Next post High Speed and Precision Type Comparator MCQ’s