The Non Inverting Configuration MCQ’s

Read Time:2 Minute, 54 Second

This set of Electronic Devices & Circuits Multiple Choice Questions & Answers (MCQs) focuses on “The Non Inverting Configuration”.

1. For ideal non-inverting operational amplifier
a) Input and output resistances are infinite
b) Input resistance is infinite and output resistance is zero
c) Input resistance is zero and output resistance is infinite
d) Input and output resistances are zero

2. For an ideal non-inverting operational amplifier having finite gain (A), the ratio of output voltage (v0) to input voltage (vi) is (given R2 is the feedback resistance)
a) (1+R2/R1)/(1+((1+R2/R1)/A))
b) (R2/R1)/(((1+R2/R1)/A))
c) (1+R2/R1)/(((1+R2/R1)/A))
d) (R2/R1)/(1+((1+R2/R1)/A))

3. In the non-inverting configuration of operational amplifier
a) The positive terminal is connected to the ground directly
b) The negative terminal is connected to the ground directly
c) The positive terminal is connected to the power source
d) The negative terminal is connected to the power source

4. The gain for an ideal non-inverting operational amplifier is (given R2 is the feedback resistance)
a) R2/R1 – 1
b) R2/R1
c) -R2/R1
d) R2/R1 + 1

5. The finite voltage gain of a non-inverting operational amplifier is A and the resistance used is R1 and R2 in which R2 is the feedback resistance. Under what conditions it can one use the expression 1 + R2/R1 to determine the gain of the amplifier?
a) A ~ R2/R1
b) A >> R2/R1
c) A << R2/R1
d) None of the mentioned

6. For designing a non-inverting amplifier with a gain of 2 at the maximum output voltage of 10 V and the current in the voltage divider is to be 10 μA the resistance required are R1 and R2 where R2 is used to provide negative feedback. Then
a) R1 = 0.5 MΩ and R2 = 0.5 MΩ
b) R1 = 0.5 kΩ and R2 = 0.5 kΩ
c) R1 = 5 MΩ and R2 = 5 MΩ
d) R1 = 5 kΩ and R2 = 5 kΩ

7. While performing an experiment to determine the gain for an ideal operational amplifier having finite gain, a student mistakenly used the equation 1 + R2/R1 where R2 is the feedback resistance. What is the percentage error in his result? Given A is the finite voltage gain of the ideal amplifier used.
a) (R2/R1)/(A+ R2/R1) X 100%
b) (1+R2/R1)/(A+R2/R1) X 100%
c) (1+R2/R1)/(A+1+R2/R1) X 100%
d) (R2/R1)/(A+1+R2/R1) X 100%

8. Which of the following is not true for a voltage follower amplifier?
a) Input voltage is equal to output voltage
b) Input resistance is infinite and output resistance is zero
c) It has 100% negative feedback
d) None of the mentioned

9. It is required to connect a transducer having an open-circuit voltage of 1 V and a source resistance of 1 MΩ to a load of 1-kΩ resistance. Find the load voltage if the connection is done (a) directly and (b) through a unity-gain voltage follower.
a) 1 μV and 1 mV respectively
b) 1 mV and 1 V respectively
c) 0.1 μV and 0.1 mV respectively
d) 0.1 mV and 0.1 V respectively

10. Consider the figure given below. If the resistance R1 is disconnected from the ground and connected to a third power source v3, then expression for the value of
v0 is

electronic-devices-circuits-questions-answers-non-inverting-configuration-q10

a) 2v1 + 4v2 − 3v3
b) 6v1 + 8v2 − 3v3
c) 6v1 + 4v2 − 9v3
d) 3v1 + 4v2 − 3v3

Happy
Happy
0 %
Sad
Sad
0 %
Excited
Excited
0 %
Sleepy
Sleepy
0 %
Angry
Angry
0 %
Surprise
Surprise
0 %

Average Rating

5 Star
0%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Leave a Reply

Your email address will not be published. Required fields are marked *

Previous post The Inverting Configuration MCQ’s
Next post Difference Amplifiers MCQ’s