Signals MCQ’s

Read Time:2 Minute, 51 Second

This set of Electronic Devices & Circuits Multiple Choice Questions & Answers (MCQs) focuses on “Signals”.

1. Which of the following is a characteristic of digital signal?
a) It takes quantized value
b) Its waveform is a continuous function
c) The maximum number of signals that can be produced by N bits is 2N-1
d) There is no loss of value after converting an analog signal to digital signal

2. Consider an N-bits ADC (Analog to Digital Converter) whose analog input varies from 0 to Vmax, then which of the following is not true?
a) The least significant bit correspond to a change of Vmax/2N -1 in the analog signal
b) The resolution of the ADC is Vmax/2N -1
c) The maximum error in the conversion (or quantization error) is Vmax/2(2N -1)
d) None of the mentioned

3. A cosine wave voltage signal has a 10V RMS value and 60Hz frequency. Also at time, t=0, the value of the voltage signal is equal to its RMS value. Which of the following is the correct mathematical representation of the voltage signal?
a) 10 cos(60t)
b) 10 cos (120πt)
c) 14.14 cos(60t + π/4)
d) 14.14 cos(120πt + π/4)

4. In compact disc (CD) audio technology, the signal is sampled at 44kHz. Each sample is represented by 16bits. What is the speed of the system in bits/second?
a) 1.34 bits/second
b) 2,750 bits/second
c) 704,000 bits/second
d) 1,441,792,000 bits/second

5. An electrical signal can be represented in either Thevenin form or Norton From. However, Norton representation is preferred when
a) The load resistance is very large as compared to the source resistance
b) The load resistance is very low as compared to the source resistance
c) There is no preferred case
d) Both of the cases mentioned are the preferred case

6. Which is the Most Significant Bit and Least Significant Bit in this case?
a) MSB: bN, LSB: bN
b) MSB: bN, LSB: b1
c) MSB: b1, LSB: bN
d) MSB: b1, LSB: b1

7. An electrical signal can be represented in either Thevenin form or Norton From. However, Thevenin representation is preferred when
a) The load resistance is very large as compared to the source resistance
b) The load resistance is very low compared to the source resistance
c) There is no preferred case.
d) Both of the cases mentioned are the preferred case

Consider the DAC (digital to Analog Converter) shown below. Where b1, b2….bn can be either 0 or 1. (Q.7 to Q.9)

8. What will be the value of the output current io, if the digital signal is in the form of b1b2b3…bn
a) Vref/2R (b1/2+ b2/4 + b3/8….+bn/(2N))
b) 2Vref/R (b1/2+ b2/4 + b3/8….+bn/(2N))
c) Vref/R (b1/2+ b2/4 + b3/8….+bn/(2N))
d) none of the above

9. For vref = 10V, n = 6, and R= 5000 ohm, which of the following is true?
a) The maximum value of the output current is 1.9375 mA
b) The change in the output current if the LSB is changed from 0 to 1 is 0.03125 mA
c) The change in the output current is the MSB is change from 0 to 1 is 0.5 mA
d) None of the mentioned

10. What is the binary representation of 57?
a) 0011 1101
b) 0101 1001
c) 0111 1001
d) 0011 1001

Happy
Happy
0 %
Sad
Sad
0 %
Excited
Excited
0 %
Sleepy
Sleepy
0 %
Angry
Angry
0 %
Surprise
Surprise
0 %

Average Rating

5 Star
0%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Leave a Reply

Your email address will not be published. Required fields are marked *

Previous post Diode Circuits MCQ’s
Next post Amplifiers MCQ’s