Advanced Problems on Measurement of Power in Polyphase Circuit MCQ’s

Read Time:2 Minute, 50 Second

This set of Electrical Measurements Multiple Choice Questions & Answers (MCQs) focuses on “Advanced Problems on Measurement of Power in Polyphase Circuit”.

1. Two watt meters, which are connected to measure the total power on a three-phase system supplying a balanced load, read 10.5 kW and – 2.5 kW respectively. What is the total power?
a) 13.0 kW
b) 13.0 kW
c) 8.0 kW
d) 8.0 kW

2. Power flowing in 3-phase, 3-wire system is measured by two wattmeter whose readings are 7000 W and -2500 W. if the voltage of the circuit is 400 V, then what will be the value of capacitance introduced in each phase to make one wattmeter reads zero? The frequency is 50 Hz.
a) 500 μF
b) 668.6 μF
c) 1000 μF
d) 748.5 μF

3. In the Two wattmeter method of measuring power in a balanced three-phase circuit, one wattmeter shows zero and the other positive maximum. The load power factor is?
a) 0
b) 0.5
c) 0.866
d) 1.0

4. A single-phase load is connected between R and Y terminals of a 220 V, symmetrical, 3-phase, 4 wire systems with phase sequence RYB. A watt-meter is connected in the system. The watt-meter will read (pf = 0.8 lagging)?
a) – 795 W
b) – 168 W
c) + 597 W
d) + 795 W

5. The ratio of the reading of 2 watt-meters connected to measure power in a balanced 3-phase load is 2: 1 and the load is inductive. The power factor of load is?
a) 0.866 lag
b) 0.615 lead
c) 0.866 lead
d) 0.625 lag

6. The two-wattmeter method is used to measure active power. The system is a 3-phase, 3- wire system. Then, the power reading is?
a) Affected by both negative sequence and zero sequence voltages
b) Affected by negative sequence voltages but not by zero sequence voltages
c) Affected by zero sequence voltages but not by negative sequence voltages
d) Not affected by negative or zero sequence voltages

7. Choose the correct statement regarding two watt-meter method for power measurements in 3-phase circuit.
a) When power factor is unity, one of the wattmeters reads zero
b) When the readings of the two watt-meters are equal but opposite sign, the power factor is zero
c) Power can be measured using two watt-meter method only for star connected 3-phase circuit
d) When two watt-meters show identical readings, the power factor is 0.5

8. In the measurement of 3-phase power by 2 watt-meter method, if the 2 watt-meter readings are equal, the power factor of the circuit is?
a) 0.8 lagging
b) 0.8 leading
c) Zero
d) Unity

9. The meter constant of a single-phase, 230 V induction watt-meter is 600 rev/kW-h. The speed of the meter disc for a current of 15 A at 0.8 power factor lagging will be?
a) 30.3 rpm
b) 25.02 rpm
c) 27.6 rpm
d) 33.1 rpm

10. The figure shows a three-phase, delta connected load supplied from a 220 V, 50 Hz, 3-phase balanced source. The pressure Coil (PC) and Current Coil (CC) of a watt-meter are connected to the load as shown, with the coil polarities suitably selected to ensure a positive deflection. The watt-meter reading will be?


a) Zero
b) 1600 W
c) 242 W
d) 400 W

Happy
Happy
0 %
Sad
Sad
0 %
Excited
Excited
0 %
Sleepy
Sleepy
0 %
Angry
Angry
0 %
Surprise
Surprise
0 %

Average Rating

5 Star
0%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Leave a Reply

Your email address will not be published. Required fields are marked *

Previous post Phase Sequence Indicator MCQ’s
Next post Advanced Miscellaneous Problems on Measurement of Power MCQ’s